Computer Controlled Wind Power Plants with Double Feed Induction Generator Application Deluxe

Product Overview

The Wind Power Plants with Double Feed Induction Generator Application, is used to investigate the design and operation of modern wind power stations.

Technical Specifications

ATENG 12383 — Computer Controlled Wind Power Plants with Double Feed Induction Generator Application

(for main items)

• With this unit there are several options and possibilities:
• Main items: 1, 2, 3 and 4.
• Optional items: 5, 6 and 7.
• Let us describe first the main items (1 to 4):
• 1AEL-WPP. Unit.
• EMT8B/1.5K. 3PH Wound Motor, 1.5 kW, 4 Poles.
• Servomotor:
• Nominal power: 2 kW.
• Nominal voltage: 3 x 400/230 VAC Y/ ?.
• Number of poles: 2.
• Frequency: 50/60 Hz.
• Speed: 3000 rpm. EMT8B/1.5K
• Nominal current: 1.7/3 A, Y/ ?.
• Asynchronous three-phase generator with double feed:
• Nominal power: 1.5 kW.
• Nominal voltage: 3 x 400/230 VAC Y/ ?.
• Frequency: 50/60 Hz
• Number of poles: 4.
• Speed: 1500 rpm.
• Nominal current: 2.5/4.4 A, Y/ ?.
• N-DFGC. Double-feed Generator Control Module.

Operation of the double-feed asynchronous generator in subsynchronous and supersynchronous

operating mode.

Autonomous control of reactive and active power, frequency, voltage, etc.

Automatic mains synchronisation.

Connection to control the back to back inverter (N-BTBINV).

Connection to control the main motor (AEL-SERIN/CA-1K).

N-DFGC

• Connection voltage: 3 x 200 V, 50…60 Hz.
• N-FRT. Fault Ride Trough Module.
• Selection of the fault type, and adjustment of its duration and angle using the touchscreen:
• Adjustment range of the fault’s duration: from 50 ms to 500 ms.
• Adjustment range of the fault’s angle: 0 to 2?.
• Graphic display:

3.8” monochrome STN display with backlight.

240 x 96 pixel resolution.

N-FRT

Safety banana connection terminals.

Push-button to start the sag.

Lighted ON/OFF switch.

Voltage sag depth availability of 0%, 20%, 40%, 60% and 80%.

• Connection voltage: 3 x 200 V, 50…60 Hz.
• N-BTBINV. Back to Back Inverter.

This module integrates a back to back inverter used to extract power from the double-feed induction

generator rotor. Besides, it integrates a braking chopper to protect the DC BUS.

The back to back inverter is controlled by the “N-DFGC” module. N-BTBINV

3

Complete Technical Specifications (for main items)

• N-SERINCA1K. Advanced Industrial Servosystems Module for AC Motors.

The “N-SERINCA1K” allows to generate wind curves configured by the user through the

AEL-WPP/CCSOF software.

The “N-SERINCA1K” consists of a control interface module connected to a three-phase motor

and a computer (AEL-PC). The control interface has a 20-bit incremental encoder that controls the

N-SERINCA1K

speed, position and torque of the motor.

The USB communication between the control interface and the PC gives the “N-SERINCA1K”

• the possibility to control the motor from the PC and to display the most important motor signals:

torque, position and speed control.

• Control Interface module:
• Three digital outputs:

Each output has a green LED that indicates if the output is active or not.

• Encoder outputs:

Two pairs of outputs (CH A Out, CH B Out and their respective denied outputs) that are TTL

signals of incremental position generated by the encoder feedback. These signals indicate the

direction of rotation of the motor.

One pair of outputs (CH Z Out and their denied) that TTL works as marker of pulses. This

signal indicates the motor speed.

• Relay output: this output is a relay, and it belongs together with the output 4 that it can be in the

software inside the I/O digital label.

• Three analog outputs: can be controlled by software to be a certain valve of the internal variables.
• Six digital inputs: digital inputs for those signals that are introduced to enable the different

available functions in the software.

• Six buttons: they are good to enable the digital inputs. When the button is pressed, the digital

Input will be activated, making what has been defined by the software.

• Six switches: they have the same function as the buttons, but with the only difference that they are

switches and, therefore, maintain the position fixed (open or closed).

• Switch outfitter of digital inputs: there is a switch that enables the digital inputs. When the green

LED is on, the inputs will be enabled.

• Analog input: this input allows an analog use directly of the user. It is an A/D input.

Potentiometer. Digital encoder.

• Reset button: this button is used to reset the motor driver after setting a new configuration.
• Motor:
• 3PH AC motor, 2 kW, 5 A, 5000 rpm, 400 VAC, 19.1 Nm, IP67, 20 bits (1048576 resolution)

incremental encoder.

• N-SERINCA1K/CCSOF: Data Management Software + Data Acquisition + Computer Control:

Compatible with actual Windows operating systems. Graphic and intuitive simulation of the

process in screen. Compatible with the industry standards.

Registration and visualization of all process variables in an automatic and simultaneous way.

Flexible open and multicontrol software, developed with actual windows graphic systems, acting

simultaneously on all process parameters. Management, processing, comparison and storage

N-SERINCA1K/CCSOF

of data. Comparative analysis of the obtained data, after the process and modification of the

conditions during the process.

4

Complete Technical Specifications (for main items)

• Required elements (Not included):
• AEL-PC. Touch Screen and Computer.
• Touch Screen:
• Energy efficiency class: A.
• Screen diagonal: 68.6 cm (27 inch (s)).
• Power consumption (operating): 26 watts.
• Annual energy consumption: 38 kWh.

AEL-PC

Power consumption (standby / off) 0.49 watts.

• Screen resolution: 1920 x 1080 pixels
• Computer:
• Processor Number: Intel Core i7-6600U Processor (4M Cache, up to 3.40 GHz).
• Cache: 4 MB Intel Smart Cache.
• Clock speed: 2.6 GHz.
• Of cores/# of threads: 2/4.
• Max. TDP/Power: 15 W.
• Memory types: DDR4-2133, LPDDDR3-1866, DDR3L-1600.
• Graphics: Intel HD Graphics 530.

Slot for PCI Express.

• AEL-WBR. Electrical Workbench (Rack).

Anodized aluminum frame.

• Melamine board, 19 mm.

Four wheels for an easy movement of the bench, two of them with safety brakes.

Fluorescent tube, 58 W.

ON/OFF selector switch.

AEL-WBR